Recent Jobs For Sterling Pool Service

December 2, 2016 | Richardson, TX

After talking to one of our pool cleaners, he said he can do this in 3 days when he's in the area. We got the pool cleaned and they are very happy to have had the help.

December 1, 2016 | Richardson, TX

We installed a new backup valve on his Polaris in the pool cleaner. We also replaced the pool sweep pump motor, seal, gasket, seal plate, impeller, and gasket. His Polaris is chugging along at full capacity now.

December 1, 2016 | Garland, TX

One of our technicians went to his house to check out the situation. They found the pump had died and needed to be replaced along with the seal, gasket, impellor, diffuser, wires, conduit and fittings on the pool pump.

November 28, 2016 | Wylie, TX

A technician went to his house and found that we needed to install a whole new pool heater with a new heat exchanger, new header gaskets, and a new flange O-ring. His timer and freeze guard had been damaged from ants chewing through the wires, we had to install a ...

November 22, 2016 | Sachse, TX

Our technician went to his house to see about these problems and found a leak the pool pump discharge. He replumbed the pool pump discharge to stop the leak and ended up having to replace the pool filter gauge entirely since the unit had gone bad.

November 21, 2016 | Plano, TX

Our owner went to her house to investigate and found that the backwash valve was old and spraying out A LOT of water! He had to replace a gasket and O-ring inside the backwash valve for it to stop leaking.

November 18, 2016 | Garland, TX

Our technician went to investigate the problem and had to replace O-rings in the suction Jandy valve, lubed the pool pump lid O-ring and programmed the pool cleaner to operate daily as an extra. This fixed his problems.

November 18, 2016 | Richardson, TX

A technician went to see what he needed and make a bid for the work. Carle approved our bid to install a new pool pump motor, seal, o-ring, wire, conduit and conduit fittings along with a new dual timer with freeze guard.

November 17, 2016 | Sachse, TX

Our owner went to narrow down the problems and found that all three of the display boards were bad, which can cause the heater to run without turning it on. He gave her a bid to install three new heater display boards in heater per manufacturer's advice then test the ...

November 17, 2016 | Mesquite, TX

Upon inspection, the best move was to install new equipment. We installed a new timer and freeze card for his pool in one box.

November 16, 2016 | Dallas, TX

Our owner went out to measure his pool and get other info before ordering the cover. He didn't want to pay for the installation of the cover so when it came in through the mail we were able to drop it off at his house. He is very pleased.

November 16, 2016 | Wylie, TX

We replaced her pool equipment, pool heater, spa blower and fully renovated new the coping, tile, gunite plaster, deck, and deco-seal. This pool looked brand new when we were finished, and she was a very elated customer.

November 2, 2016 | Allen, TX

Sterling Pool Service's owner made it to this guys house and needed to repair the plumbing leaks in order to stop them. He evaluated the gentleman's filter and found it was not in need of a filter clean at this time.

November 2, 2016 | Wylie, TX

Our owner went to her house to put a bid together. The bid looked good to her but needed to put the funds together. While waiting, a major hail storm struck the area and wreaked havoc on her pool. What began as a bid for three items turned into much ...

November 1, 2016 | Plano, TX

Our owner went to her house to see about the problem and found he needed to replace the O-rings in the Jandy valve. He also found a leak at the filter and had to replace the handle and O-rings on the backwash valve.