Recent Jobs For Sterling Pool Service

December 20, 2018 | Murphy, TX

When we arrived on-site, the owner of the company found that the water flow pressure was caused by a large volume of leaves and dirt that had been blown/washed into the pool because of storms. The debris had clogged the filter. A backwash alone did not solve the pressure ...

December 20, 2018 | Allen, TX

The owner of the company went to her house to see why her heater controller showed the message "water sensor shorted." Luckily, the message she was getting was accurate and the issue was readily solved by replacing the water temperature sensor for the computer. Once that repair was made, everything ...

November 26, 2018 | Plano, TX

Our technician went to diagnose the problem and found it relatively easily. When the pool and automatic pool sweep were running, he noticed the white hose for the booster pump was leaking badly because of a split. He replaced the broken hose section and this fixed the leak.

November 21, 2018 | Plano, TX

The owner went to see about the issues with Randy's pool pump and pump housing. After thoroughly inspecting the pump, he found that it was beyond repair. He had to install a new pool pump motor, seal, and gasket. He also lubricated the backwash push/pull valve.

November 19, 2018 | Wylie, TX

The owner went to inspect the issues involving the pool valve and the pool sweep that same day. He found the computer motherboard needed to be replaced, along with the Polaris pool sweep cleaner booster pump. Tony approved both items the same day and we replaced them. His weekly pool ...

October 18, 2018 | Dallas, TX

The owner of Sterling Pools made an appointment to investigate this slow leak. When he was checking the connections inside and outside of the heater, he noticed the heat exchanger and gaskets were worn out and caused the leak. He had to order parts. After the parts arrived, he went ...

October 18, 2018 | Plano, TX

Sterling Pools' owner went to Patrick's house for further investigation of the leaking Polaris pump. The Polaris booster pump volute was not the only problem. He discovered three electrical connections that had gone bad and were arching between each other. To make the repair, Patrick needed a new Polaris booster ...

October 10, 2018 | Murphy, TX

After looking at Mark's pool pump, we suggested his variable speed pump was running at too low of a speed and needed to be set at a faster level. This did not solve the problem, so the owner of Sterling Pools went to his house. After a thorough inspection of ...

October 10, 2018 | Allen, TX

Our owner already was in her area when I called to give him the message about the spa that drained unexpectedly. He went by and noticed the same thing when he turned on the spa. After inspecting the equipment for any leaks or damage, he found the spa valve was ...

October 8, 2018 | Dallas, TX

After spotting the issue, Jose solved the problem while on his scheduled cleaning service call. Jose is a versatile and effective technician who had replacement parts on his truck. He was able to replace the affected parts. The Polaris pool sweep is now running all over the pool again picking ...

October 8, 2018 | Wylie, TX

The owner of Sterling Pool Service, who is a licensed pool electrician, went to his house and inspected both his pool and spa lights. It turned out the GFI was in good shape but the light fixture for the pool needed to be replaced. Because his lights were color changing, ...

October 2, 2018 | Plano, TX

When we arrived at Debbie's house, the owner lubed the pump lid O-ring and tightened a few nuts on the pump and motor in addition to repeating Debbie's efforts. This did not fix the problem. He then checked the plumbing going into the pool pump and found a slight leak. ...

October 2, 2018 | Plano, TX

Our lead technician went to Debbie's house to look at the pool pump. He had to repair a suction leak on the pool pump in order to get it to prime consistently. Once repaired, it performed consistently.

August 23, 2018 | Parker, TX

Sterling Pool Service's owner went to Jim's house and installed a new factory-replacement, high-pressure, corrosion and chlorine-resistant hose. The manufactured hose at Jim's house had failed, causing the leak.

August 20, 2018 | Plano, TX

The owner Kevin went to their house to inspect the pool light. He found that the entire light fixture was defective, which prevented the bulb from working. He replaced the fixture and Jenifer chose a 500-watt equivalent white LED pool light with the new fixture. Everything works smoothly now.