Recent Jobs For Sterling Pool Service

February 28, 2018 | Wylie, TX

Sterling Pool Service's owner went over to Larry's to start everything and the pool pump motor cracked when he switched it on. This was due to the extended freeze causing damage we couldn't see. We gave him a bid to replace the pool pump motor and we completed the install ...

January 27, 2018 | Wylie, TX

The company owner went to inspect this issue. He found that they needed a new pool timer and freeze guard mechanism for the equipment. In addition, the pump motor had a bad capacitor. He replaced the capacitor and the timer/freeze guard but found a loose wire connecting the timer ...

January 22, 2018 | Dallas, TX

We had his technician look for any issues and he was able to find some cracks that had formed inside of the skimmer throat. Luckily, this was a relatively simple fix. The owner had to drain the pool below the skimmer, reset tile inside the skimmer and seal the skimmer ...

January 12, 2018 | Wylie, TX

Upon inspecting Irina's pool equipment, he found a bad O-ring in the backwash valve. He replaced the bad O-ring in the backwash valve and had to lube the stem O-ring. After that, no more water showed on the equipment pad and the pool stopped losing water.

January 11, 2018 | Garland, TX

Once the leak detection appointment was made, we sent a team to Louanne's house. We found the culprit(s) to be the angled shear descents that are on the pool walls. Our company owner was able to cosmetically repair all three dents with a rapid-setting mortar and the leaks have ...

December 18, 2017 | Plano, TX

After the cold weather set in, she called us to come out again to troubleshoot and our company owner found the top half of the filter had cracked. We gave her two options: 1. Replace the top filter half or 2. Replace the filter entirely. She chose option 2, to replace the entire ...

November 29, 2017 | Bedford, TX

The company owner went to check it out and found her pool sweep pump had stopped working. The only solution to this problem was to replace the pump. He did this and her Polaris started working great again.

November 17, 2017 | Richardson, TX

Our owner Kevin presented him with several options for updating the equipment pad and heater. Carle decided on a new equipment pad and used 400,000 BTU Pentair master temp heater.

October 31, 2017 | Dallas, TX

Our owner Kevin went to look at his problems and found a number of issues. We got approval for turning his pool around and had to clean the filter as well as replace eight filter grids. We also balanced the chemicals, shocked the pool, brushed away the algae, vacuumed one ...

October 27, 2017 | Plano, TX

The company owner went to investigate and advised that a leak detection be done. The results of the leak detection showed the deep end skimmer needed to replaced. It was replaced and the pool is performing well.

October 19, 2017 | Dallas, TX

The owner went to his house a week later to take measurements. After he confirmed his numbers with Loop 'N Lock, he quoted Billy a price and Billy agreed. Drilling the holes took a couple of days, but now the pool cover is on and Billy is happy with our ...

September 18, 2017 | Murphy, TX

Sterling Pool Service's owner went to evaluate the pool motor. The motor did not need to be replaced but he did replace the seal and gasket then evaluated the performance. The pool motor checked out after he was finished.

September 5, 2017 | Plano, TX

The owner went back over to see what could be done. We submitted a bid offering three different options with a low, medium and high-end figure. He chose to have a white LED pool light fixture installed, though he is still interested in a color changing LED pool light fixture ...

August 25, 2017 | Rowlett, TX

After Norman gave us the green light to start the pool remodel, our crew showed up the following week. We helped him pick out the perfect tile, coping, grout color and pool plaster color/type. He chose a standard white plaster, went with terra blue tile, and chose Oklahoma multi-color ...

August 24, 2017 | Dallas, TX

Our lead technician went to evaluate his problem. He had to install a new pool pump motor, seal and gasket. This stopped the high-pitched noises and made Richard and his wife very happy.